ATI Professional Welding Section 3A Flux-core MIG Welding.Introduction to flux-core welding.Watch this flux core video..
MIG Weld How To - SHIELDING GAS
General. Most metals exhibit a strong tendency to combine with oxygen (to form oxides) and to a lesser extent with nitrogen (to form metal nitrides). Oxygen will also react with carbon to form carbon monoxide gas. These reaction products are all a source of weld deficiencies in the form of: fusion defects due to oxides; loss of strength due to porosity, oxides and nitrides; and weld metal embrittlement due to dissolved oxides and nitrides. These reaction products are easily formed since the atmosphere is more or less composed of 80 percent nitrogen and 20 percent oxygen. The primary function of the shielding gas is to exclude the surrounding atmosphere from contact with the molten weld metal.
The shielding gas will also have a pronounced effect upon the following aspects of the welding operation and the resultant weld:
1. Arc characteristics
2. Mode of metal transfer
3. Penetration and weld bead profile
4. Speed of welding
5. Undercutting tendency
6. Cleaning action
The Inert Shielding Gases — Argon and Helium. Argon and helium are inert gases. These gases and mixtures of the two are necessarily used in the welding of nonferrous metals and also widely used to weld stainless steel and low alloy steels.
Basic differences between argon and helium are:
1. Density
2. Thermal conductivity
3. Arc characteristics
Various shielding gases
Relative effect of O2 versus CO2 additions to the argon shield.
The shielding gas will also have a pronounced effect upon the following aspects of the welding operation and the resultant weld:
1. Arc characteristics
2. Mode of metal transfer
3. Penetration and weld bead profile
4. Speed of welding
5. Undercutting tendency
6. Cleaning action
The Inert Shielding Gases — Argon and Helium. Argon and helium are inert gases. These gases and mixtures of the two are necessarily used in the welding of nonferrous metals and also widely used to weld stainless steel and low alloy steels.
Basic differences between argon and helium are:
1. Density
2. Thermal conductivity
3. Arc characteristics
Various shielding gases
Relative effect of O2 versus CO2 additions to the argon shield.
MIG Weld How To - Setting Wire Speed and Voltage
Setting Wire Speed and Voltage
Power Supply Variables. The self-correcting arc property of the (CV) power supply is important in producing stable welding conditions, but there are additional adjustments necessary to produce the best possible condition. These are particularly important for short circuiting welding.
Voltage. Arc voltage is the electrical potential between the electrode and the workpiece. This voltage cannot be directly read at the power supply because other voltage drops exist throughout the welding system. The arc voltage varies in the same direction as the arc length; therefore, increasing or decreasing the output voltage of the power source will increase or decrease the arc length.
Or wire feed weld :)
Power Supply Variables. The self-correcting arc property of the (CV) power supply is important in producing stable welding conditions, but there are additional adjustments necessary to produce the best possible condition. These are particularly important for short circuiting welding.
Voltage. Arc voltage is the electrical potential between the electrode and the workpiece. This voltage cannot be directly read at the power supply because other voltage drops exist throughout the welding system. The arc voltage varies in the same direction as the arc length; therefore, increasing or decreasing the output voltage of the power source will increase or decrease the arc length.
Or wire feed weld :)
MIG Weld How To - MIG Welding Principles
Principles, procedures, and techniques. What happens at the MIG arc? Identifies weld equipment and setup before welding.
The GMAW process was developed and made commercially available in 1948, although the basic concept was actually introduced in the 1920’s. In its early commercial applications, the process was used to weld aluminum with an inert shielding gas, giving rise to the term “MIG” (metal inert gas) which is still commonly used when referring to the process. Variations have been added to the process, among which was the use of active shielding gases, particularly CO2, for welding certain ferrous metals. This eventually led to the formally accepted AWS term of gas metal arc welding (GMAW) for the process. Further developments included the short circuiting mode of metal transfer (GMAW-S), a lower heat energy variation of the process that permits welding out-of-position and also on materials of sheet metal thicknesses; and a method of controlled pulsating current (GMAW-P) to provide a uniform spray droplet metal transfer from the electrode at a lower average current levels.
The GMAW process uses either semiautomatic or automatic equipment and is principally applied in high duction welding. Most metals can be welded with this process and may be welded in all positions with the lower energy variations of the process. GMAW is an economical process that requires little or no cleaning of the weld deposit. Warpage is reduced and metal finishing is minimal compared to stick welding.
FUNDAMENTALS
Principles of Operation. GMAW is an arc welding process which incorporates the automatic feeding of a continuous, consumable electrode that is shielded by an externally supplied gas. Since the equipment provides for automatic selfregulation of the electrical characteristics of the arc and deposition rate, the only manual controls required by the welder for semiautomatic operation are gun positioning, guidance, and travel speed. The arc length and the current level are automatically maintained. Process control and function are achieved through these three basic elements of equipment :
1. Gun and cable assembly
2. Wire feed unit
3. Power source
MIG Weld How TO - EQUIPMENT
The MIG process can be used either semiautomatically or automatically. The basic equipment for any MIG installation consist of the following:
1. A welding gun
2. A wire feed motor and associated gears or drive rolls
3. A welding control
4. A welding power source
5. A regulated supply of shielding gas
6. A supply of electrode
7. Interconnecting cables and hoses
MIG How To - Semiautomatic gas metal arc welding installation.
The GMAW process was developed and made commercially available in 1948, although the basic concept was actually introduced in the 1920’s. In its early commercial applications, the process was used to weld aluminum with an inert shielding gas, giving rise to the term “MIG” (metal inert gas) which is still commonly used when referring to the process. Variations have been added to the process, among which was the use of active shielding gases, particularly CO2, for welding certain ferrous metals. This eventually led to the formally accepted AWS term of gas metal arc welding (GMAW) for the process. Further developments included the short circuiting mode of metal transfer (GMAW-S), a lower heat energy variation of the process that permits welding out-of-position and also on materials of sheet metal thicknesses; and a method of controlled pulsating current (GMAW-P) to provide a uniform spray droplet metal transfer from the electrode at a lower average current levels.
The GMAW process uses either semiautomatic or automatic equipment and is principally applied in high duction welding. Most metals can be welded with this process and may be welded in all positions with the lower energy variations of the process. GMAW is an economical process that requires little or no cleaning of the weld deposit. Warpage is reduced and metal finishing is minimal compared to stick welding.
FUNDAMENTALS
Principles of Operation. GMAW is an arc welding process which incorporates the automatic feeding of a continuous, consumable electrode that is shielded by an externally supplied gas. Since the equipment provides for automatic selfregulation of the electrical characteristics of the arc and deposition rate, the only manual controls required by the welder for semiautomatic operation are gun positioning, guidance, and travel speed. The arc length and the current level are automatically maintained. Process control and function are achieved through these three basic elements of equipment :
1. Gun and cable assembly
2. Wire feed unit
3. Power source
MIG Weld How TO - EQUIPMENT
The MIG process can be used either semiautomatically or automatically. The basic equipment for any MIG installation consist of the following:
1. A welding gun
2. A wire feed motor and associated gears or drive rolls
3. A welding control
4. A welding power source
5. A regulated supply of shielding gas
6. A supply of electrode
7. Interconnecting cables and hoses
MIG How To - Semiautomatic gas metal arc welding installation.
Subscribe to:
Posts (Atom)





